$NE=[ ]; = local needle-orientation to control the yarn feeder by the user and not by intarsia-fields
- [R]= repeats from edge to intarsia-field
- [V]= repeats from edge and including intarsia-field (against move)
- [F]= fix-area in front of intarsia-field
- [W]= fix-area at the edge (against moving)
- [A]= fix-area at the edge (in direction moving)
- [O]= fix-area in the intarsia-field
- ,RG = Needle-bed in Ground position
- ,RU1 = Transfer-Rack for knitting with front and back stitch and transfer
- ,RU2 = Transfer-Rack only for knitting with front or back stitch and transfer
- ,RU = System is looking for the best transfer-rack (RU1 or RU2)
- ,NEW_CARRIAGE = to force a new carriage
- ,GO<= force a carriage to the left
- ,GO>= force a carriage to the right
- LOOKSEL= Use only Needles which have Stitch or Tuck
- ,FIX= transfer all selected needles (also needles without stitches)
- ,JAC-3> = JACQUARD-Main-Rack ( in this case: 3 needles to right; also 'JAC->>>' possible )
- ,TZ1= Speed-Variables (look in machine-parameter)
- ...,TZ19
- ,WA1= Take-Down-Variables (look in machine-parameter)
- ...,WA19
- ,FS1= Tension-Variables (look in tension-parameter)
- …,FS19
- ,LFS1= Leading stitch graduation
- ...,LFS7
- F_tSHORT= short Tuck on the comp-level front-needle-bed
- R_tSHORT= short Tuck on the comp-level back-needle-bed
- ,F_SC1= front Needle bed to knit 1.Color from DESIGN
- ,R_SC2= back Needle bed to knit 2.Color from DESIGN
- ,F_TC1= front Needle bed make tuck 1.Color from DESIGN
- ,F_UC3= back Needle bed to transfer 3.Color from DESIGN
- ,R_SNF= back needle-bed only select if front needle-bed not select
- ,C1,C2 ec. from Column 3,4 ec. in DESIGN-level (edge column left)
- ,YC_SQ1= describe the sequence in the CTRL YC-Level
- ..,YC_SQ6
- ,GRO1= open Gripper outside left
- ,GRO2= open Gripper inside left
- ,GRO3= open Gripper inside right
- ,GRO4= open Gripper outside right
- ,GRC1= close Gripper outside left
- ,GRC2= close Gripper inside left
- ,GRC3= close Gripper inside right
- ,GRC4= close Gripper outside right
- ,SCL= Cutter left
- ,SCR= Cutter right
- ,SCLR= Cutter left and right
- ,SCA= Cutter automatically cut after the comb is outside and the main-takedown has closed
- ,VSINKER1= Sinker for front in half position(Protti)
- ,VSINKER2= Sinker for front in low position(Protti)
- ,HSINKER1= Sinker for rear in half position(Protti)
- ,HSINKER2= Sinker for rear in low position(Protti)
- ,PRS_OFF = switch off the stitch-presser
- ,REPBEG= variable amount of knitting-rows in a weave start-line
- ,REPEND= variable amount of knitting-rows in a weave end-line
in the function-set add the parameter ',REP10,' for exc. 10 times
- ,PRESSOFF-2= or
- ,FALLDOWN-2= if stitch selected on a empty needle, after two phases the stitch will be pressed off;
- ,F_UB = transfer from front-needle-bed to upper back-help-needle-bed
- ,F_UF = transfer from front-needle-bed to upper front-help-needle-bed,
- ,F_NB = receive from upper back-help-needle-bed to front-needle-bed
- ,R_UB = transfer from back-needle-bed to upper back-help-needle-bed,
- ,R_UF = transfer from back-needle-bed to upper front-help-needle-bed
- ,R_NF = receive from upper front-help-needle-bed to back-needle-bed
With Rack:
for exc. ,F_UB>>> or ,F_UB3>;
Intarsia Function-Set
This function-Set is used for all Yarn feeder-movements:
- ,YC-NOFUN = no function, is used if the System can't find a correct Intarsia-Function;
- ,YC-INEL = Intarsia-link going into field; course: left to right;
- ,YC-INER = Intarsia-link going into field; course: right to left;
- ,YC-INAL = Intarsia-link going out-side field; course: left to right;
- ,YC-INAR = Intarsia-link going out-side field; course: right to left;
- ,YC-KPML = to go in position from left edge; course: left to right;
- ,YC-KPMR = to go in position from right edge; course: right to left;
- ,YC-KPGL = to go in position from right edge; course: left to right;
- ,YC-KPGR = to go in position from left edge; course: right to left;
- ,YC-HPML = to go in right park-position; course: left to right;
- ,YC-HPMR = to go in left park-position; course: right to left;
- ,YC-HPGL = to go in left park-position; course: left to right;
- ,YC-HPGR = to go in right park-position; course: right to left;
- ,YC-IN??,1X1, = alter. Intarsia-link for correction-correction one by one
- ,YC-IN??,NETZ,= alternative Intarsia-link for ladder-back;
- ,YC-IN??,HTECH= Correct Yarn feeder position. With function of STRUCTUR-level
Following parameters could be edit only in [Modexcomp]=1 mode:
- ,JAC-= save Stitches in neighbourhood before of JACQUARD-Rack
- ^= Transfer Needle from front to back
- V= transfer Needle from back to front
- ,SAVE-U= save Stitches before Rack-Transfer
(only used for intarsia-function)
- ,REST-U= restore Stitches after Rack-Transfer
(only used for intarsia-function)
- ,FSCONTROL_OFF = Ignore DSCS for this Carriage way;
- ,F_UNR= (R_UNF) only transfer in empty needle
- ,F_SNET= only select if the stitch was created before on a empty needle
(only in combination of the command PRESSOFF in a element before)
- ,NZ_A1 ..,NZ_F3 ,NZ_VAR (variable) =UNIVERSAL MC600 Ladder-Back-Techno:
- ,TROW_RG1 ( YH1,-[*] ) =Direct-Address of Pattern only for the first 10 pattern lines